DaVinci: fix GPIO breakage after v4.19
This set of changes is needed to fix the broken GPIO support
for DaVinci boards in legacy mode after certain changes made to the
GPIO driver in 4.19, namely: commits
587f7a694f01 ("gpio: davinci: Use
dev name for label and automatic base selection") and
eb3744a2dd01
("gpio: davinci: Do not assume continuous IRQ numbering").
* tag 'davinci-fixes-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: dm644x: set the GPIO base to 0
ARM: davinci: da830: set the GPIO base to 0
ARM: davinci: dm355: set the GPIO base to 0
ARM: davinci: dm646x: set the GPIO base to 0
ARM: davinci: dm365: set the GPIO base to 0
ARM: davinci: da850: set the GPIO base to 0
gpio: davinci: restore a way to manually specify the GPIO base
ARM: davinci: dm644x: define gpio interrupts as separate resources
ARM: davinci: dm355: define gpio interrupts as separate resources
ARM: davinci: dm646x: define gpio interrupts as separate resources
ARM: davinci: dm365: define gpio interrupts as separate resources
ARM: davinci: da8xx: define gpio interrupts as separate resources
Signed-off-by: Olof Johansson <olof@lixom.net>
compatible = "renesas,r8a77470"
- RZ/G2M (R8A774A1)
compatible = "renesas,r8a774a1"
- - RZ/G2E (RA8774C0)
+ - RZ/G2E (R8A774C0)
compatible = "renesas,r8a774c0"
- R-Car M1A (R8A77781)
compatible = "renesas,r8a7778"
BROADCOM BCM5301X ARM ARCHITECTURE
M: Hauke Mehrtens <hauke@hauke-m.de>
M: Rafał Miłecki <zajec5@gmail.com>
-M: Jon Mason <jonmason@broadcom.com>
M: bcm-kernel-feedback-list@broadcom.com
L: linux-arm-kernel@lists.infradead.org
S: Maintained
BROADCOM IPROC ARM ARCHITECTURE
M: Ray Jui <rjui@broadcom.com>
M: Scott Branden <sbranden@broadcom.com>
-M: Jon Mason <jonmason@broadcom.com>
M: bcm-kernel-feedback-list@broadcom.com
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
T: git git://github.com/broadcom/cygnus-linux.git
};
chosen {
- stdout-path = "&uart1:115200n8";
+ stdout-path = "serial0:115200n8";
};
memory@70000000 {
i2c1: i2c@21a0000 {
#address-cells = <1>;
#size-cells = <0>;
- compatible = "fs,imx6sll-i2c", "fsl,imx21-i2c";
+ compatible = "fsl,imx6sll-i2c", "fsl,imx21-i2c";
reg = <0x021a0000 0x4000>;
interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6SLL_CLK_I2C1>;
regulator-name = "enet_3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
- gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
+ gpio = <&gpio2 6 GPIO_ACTIVE_LOW>;
+ regulator-boot-on;
+ regulator-always-on;
};
reg_pcie_gpio: regulator-pcie-gpio {
phy-supply = <®_enet_3v3>;
phy-mode = "rgmii";
phy-handle = <ðphy1>;
+ phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
status = "okay";
mdio {
MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 0x3081
MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081
MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M 0x91
+ /* phy reset */
+ MX6SX_PAD_ENET2_CRS__GPIO2_IO_7 0x10b0
>;
};
#include "rk3288.dtsi"
/ {
- memory@0 {
+ /*
+ * The default coreboot on veyron devices ignores memory@0 nodes
+ * and would instead create another memory node.
+ */
+ memory {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
0x1 0x0 0x60000000 0x10000000
0x2 0x0 0x70000000 0x10000000
0x3 0x0 0x80000000 0x10000000>;
- clocks = <&mck>;
+ clocks = <&h32ck>;
status = "disabled";
nand_controller: nand-controller {
compatible = "fsl,vf610m4";
chosen {
- bootargs = "console=ttyLP2,115200 clk_ignore_unused init=/linuxrc rw";
- stdout-path = "&uart2";
+ bootargs = "clk_ignore_unused init=/linuxrc rw";
+ stdout-path = "serial2:115200";
};
memory@8c000000 {
CONFIG_SYSVIPC=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
CONFIG_CGROUPS=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_EMBEDDED=y
clock-names = "stmmaceth";
tx-fifo-depth = <16384>;
rx-fifo-depth = <16384>;
+ snps,multicast-filter-bins = <256>;
status = "disabled";
};
clock-names = "stmmaceth";
tx-fifo-depth = <16384>;
rx-fifo-depth = <16384>;
+ snps,multicast-filter-bins = <256>;
status = "disabled";
};
clock-names = "stmmaceth";
tx-fifo-depth = <16384>;
rx-fifo-depth = <16384>;
+ snps,multicast-filter-bins = <256>;
status = "disabled";
};
};
};
};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+};
status = "okay";
};
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+};
+
&uart9 {
status = "okay";
};
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x35>, <&dmac1 0x34>,
<&dmac2 0x35>, <&dmac2 0x34>;
- dma-names = "tx", "rx";
+ dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
resets = <&cpg 518>;
status = "disabled";
aliases {
serial0 = &scif0;
- ethernet0 = &avb;
+ ethernet0 = &gether;
};
chosen {
};
};
-&avb {
- pinctrl-0 = <&avb_pins>;
- pinctrl-names = "default";
-
- phy-mode = "rgmii-id";
- phy-handle = <&phy0>;
- renesas,no-ether-link;
- status = "okay";
-
- phy0: ethernet-phy@0 {
- rxc-skew-ps = <1500>;
- reg = <0>;
- interrupt-parent = <&gpio1>;
- interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
- };
-};
-
&canfd {
pinctrl-0 = <&canfd0_pins>;
pinctrl-names = "default";
clock-frequency = <32768>;
};
+&gether {
+ pinctrl-0 = <&gether_pins>;
+ pinctrl-names = "default";
+
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy0>;
+ renesas,no-ether-link;
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ rxc-skew-ps = <1500>;
+ reg = <0>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
&i2c0 {
pinctrl-0 = <&i2c0_pins>;
pinctrl-names = "default";
};
&pfc {
- avb_pins: avb {
- groups = "avb_mdio", "avb_rgmii";
- function = "avb";
- };
-
canfd0_pins: canfd0 {
groups = "canfd0_data_a";
function = "canfd0";
};
+ gether_pins: gether {
+ groups = "gether_mdio_a", "gether_rgmii",
+ "gether_txcrefclk", "gether_txcrefclk_mega";
+ function = "gether";
+ };
+
i2c0_pins: i2c0 {
groups = "i2c0";
function = "i2c0";
};
&pcie0 {
- ep-gpios = <&gpio4 RK_PC6 GPIO_ACTIVE_LOW>;
+ ep-gpios = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
num-lanes = <4>;
pinctrl-names = "default";
pinctrl-0 = <&pcie_clkreqn_cpm>;
regulator-always-on;
vin-supply = <&vcc_sys>;
};
-
- vdd_log: vdd-log {
- compatible = "pwm-regulator";
- pwms = <&pwm2 0 25000 0>;
- regulator-name = "vdd_log";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vcc_sys>;
- };
-
};
&cpu_l0 {
wkup_uart0: serial@42300000 {
compatible = "ti,am654-uart";
- reg = <0x00 0x42300000 0x00 0x100>;
+ reg = <0x42300000 0x100>;
reg-shift = <2>;
reg-io-width = <4>;
interrupts = <GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>;