xirc2ps_cs= [NET,PCMCIA]
Format:
<irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
+
+ xhci-hcd.quirks [USB,KNL]
+ A hex value specifying bitmask with supplemental xhci
+ host controller quirks. Meaning of each bit can be
+ consulted in header drivers/usb/host/xhci.h.
``intel_pstate`` exposes several global attributes (files) in ``sysfs`` to
control its functionality at the system level. They are located in the
-``/sys/devices/system/cpu/cpufreq/intel_pstate/`` directory and affect all
-CPUs.
+``/sys/devices/system/cpu/intel_pstate/`` directory and affect all CPUs.
Some of them are not present if the ``intel_pstate=per_cpu_perf_limits``
argument is passed to the kernel in the command line.
but it affects the maximum possible value of per-policy P-state limits
(see `Interpretation of Policy Attributes`_ below for details).
+``hwp_dynamic_boost``
+ This attribute is only present if ``intel_pstate`` works in the
+ `active mode with the HWP feature enabled <Active Mode With HWP_>`_ in
+ the processor. If set (equal to 1), it causes the minimum P-state limit
+ to be increased dynamically for a short time whenever a task previously
+ waiting on I/O is selected to run on a given logical CPU (the purpose
+ of this mechanism is to improve performance).
+
+ This setting has no effect on logical CPUs whose minimum P-state limit
+ is directly set to the highest non-turbo P-state or above it.
+
.. _status_attr:
``status``
size)
5. the number of optional parameters (the parameters with an argument
count as two)
+ start_sector n (default: 0)
+ offset from the start of cache device in 512-byte sectors
high_watermark n (default: 50)
start writeback when the number of used blocks reach this
watermark
- "insignal,arndale-octa" - for Exynos5420-based Insignal Arndale
Octa board.
- "insignal,origen" - for Exynos4210-based Insignal Origen board.
- - "insignal,origen4412 - for Exynos4412-based Insignal Origen board.
+ - "insignal,origen4412" - for Exynos4412-based Insignal Origen board.
Optional nodes:
- port/ports: to describe a connection to an external encoder. The
binding follows Documentation/devicetree/bindings/graph.txt and
- suppors a single port with a single endpoint.
+ supports a single port with a single endpoint.
- See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and
Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting
Nintendo Wii (Hollywood) GPIO controller
Required properties:
-- compatible: "nintendo,hollywood-gpio
+- compatible: "nintendo,hollywood-gpio"
- reg: Physical base address and length of the controller's registers.
- gpio-controller: Marks the device node as a GPIO controller.
- #gpio-cells: Should be <2>. The first cell is the pin number and the
--- /dev/null
+Spreadtrum SC27xx PMIC Vibrator
+
+Required properties:
+- compatible: should be "sprd,sc2731-vibrator".
+- reg: address of vibrator control register.
+
+Example :
+
+ sc2731_pmic: pmic@0 {
+ compatible = "sprd,sc2731";
+ reg = <0>;
+ spi-max-frequency = <26000000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vibrator@eb4 {
+ compatible = "sprd,sc2731-vibrator";
+ reg = <0xeb4>;
+ };
+ };
reg = <0x6c>;
interrupt-parent = <&gpx1>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
- vdd-supply = <&ldo15_reg>";
+ vdd-supply = <&ldo15_reg>;
vid-supply = <&ldo18_reg>;
reset-gpios = <&gpx1 5 0>;
touchscreen-size-x = <1080>;
include "nvidia,tegra30-ictlr".
- reg : Specifies base physical address and size of the registers.
Each controller must be described separately (Tegra20 has 4 of them,
- whereas Tegra30 and later have 5"
+ whereas Tegra30 and later have 5).
- interrupt-controller : Identifies the node as an interrupt controller.
- #interrupt-cells : Specifies the number of cells needed to encode an
interrupt source. The value must be 3.
specifier, shall be 2
- interrupts: interrupts references to primary interrupt controller
(only needed for exti controller with multiple exti under
- same parent interrupt: st,stm32-exti and st,stm32h7-exti")
+ same parent interrupt: st,stm32-exti and st,stm32h7-exti)
Example:
- compatible : should contain one of:
"brcm,bcm7425-timers"
"brcm,bcm7429-timers"
- "brcm,bcm7435-timers and
+ "brcm,bcm7435-timers" and
"brcm,brcmstb-timers"
- reg : the timers register range
- interrupts : the interrupt line for this timer block
Must include one of the following:
- "fsl,fman-dtsec" for dTSEC MAC
- "fsl,fman-xgec" for XGEC MAC
- - "fsl,fman-memac for mEMAC MAC
+ - "fsl,fman-memac" for mEMAC MAC
- cell-index
Usage: required
node with the label "power".
In the second example the consumer device are partitioned across two PM domains,
the first with index 0 and the second with index 1, of a power controller that
-is represented by a node with the label "power.
+is represented by a node with the label "power".
Optional properties:
- required-opps: This contains phandle to an OPP node in another device's OPP
Optional properties:
- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
If DCDCs are externally controlled then this property should be there.
-- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
+- dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
If DCDCs are externally controlled and if it is from GPIO then GPIO
number should be provided. If it is externally controlled and no GPIO
entry then driver will just configure this rails as external control
controller binding usage.
Required properties:
-- compatible: Should be st,stih407-softreset";
+- compatible: Should be "st,stih407-softreset";
- #reset-cells: 1, see below
example:
Optional property:
- clock-frequency: Desired I2C bus clock frequency in Hz.
- When missing default to 400000Hz.
+ When missing default to 100000Hz.
Child nodes should conform to I2C bus binding as described in i2c.txt.
Board connectors:
* Headset Mic
- * Secondary Mic",
+ * Secondary Mic
* DMIC
* Ext Spk
"Digital Mic3"
Audio pins and MicBias on WCD9335 Codec:
- "MIC_BIAS1
+ "MIC_BIAS1"
"MIC_BIAS2"
"MIC_BIAS3"
"MIC_BIAS4"
the node is not important. The content of the node is defined in dwc3.txt.
Phy documentation is provided in the following places:
-Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
+Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt - USB2.0 PHY
+Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt - Type-C PHY
Example device nodes:
Examples:
- onewire@0 {
+ onewire {
compatible = "w1-gpio";
gpios = <&gpio 126 0>, <&gpio 105 0>;
};
int (*iterate) (struct file *, struct dir_context *);
int (*iterate_shared) (struct file *, struct dir_context *);
__poll_t (*poll) (struct file *, struct poll_table_struct *);
- struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
- __poll_t (*poll_mask) (struct file *, __poll_t);
long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
int (*mmap) (struct file *, struct vm_area_struct *);
};
locking rules:
- All except for ->poll_mask may block.
+ All may block.
->llseek() locking has moved from llseek to the individual llseek
implementations. If your fs is not using generic_file_llseek, you
the lease within the individual filesystem to record the result of the
operation
-->poll_mask can be called with or without the waitqueue lock for the waitqueue
-returned from ->get_poll_head.
-
--------------------------- dquot_operations -------------------------------
prototypes:
int (*write_dquot) (struct dquot *);
ssize_t (*write_iter) (struct kiocb *, struct iov_iter *);
int (*iterate) (struct file *, struct dir_context *);
__poll_t (*poll) (struct file *, struct poll_table_struct *);
- struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
- __poll_t (*poll_mask) (struct file *, __poll_t);
long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
int (*mmap) (struct file *, struct vm_area_struct *);
activity on this file and (optionally) go to sleep until there
is activity. Called by the select(2) and poll(2) system calls
- get_poll_head: Returns the struct wait_queue_head that callers can
- wait on. Callers need to check the returned events using ->poll_mask
- once woken. Can return NULL to indicate polling is not supported,
- or any error code using the ERR_PTR convention to indicate that a
- grave error occured and ->poll_mask shall not be called.
-
- poll_mask: return the mask of EPOLL* values describing the file descriptor
- state. Called either before going to sleep on the waitqueue returned by
- get_poll_head, or after it has been woken. If ->get_poll_head and
- ->poll_mask are implemented ->poll does not need to be implement.
-
unlocked_ioctl: called by the ioctl(2) system call.
compat_ioctl: called by the ioctl(2) system call when 32 bit system calls
--------------------------------------------------
Additional options used for $(LD) when linking modules.
+KBUILD_KCONFIG
+--------------------------------------------------
+Set the top-level Kconfig file to the value of this environment
+variable. The default name is "Kconfig".
+
KBUILD_VERBOSE
--------------------------------------------------
Set the kbuild verbosity. Can be assigned same values as "V=...".
directory name found in the arch/ directory.
But some architectures such as x86 and sparc have aliases.
x86: i386 for 32 bit, x86_64 for 64 bit
-sparc: sparc for 32 bit, sparc64 for 64 bit
+sh: sh for 32 bit, sh64 for 64 bit
+sparc: sparc32 for 32 bit, sparc64 for 64 bit
CROSS_COMPILE
--------------------------------------------------
the default option --strip-debug will be used. Otherwise,
INSTALL_MOD_STRIP value will be used as the options to the strip command.
-INSTALL_FW_PATH
---------------------------------------------------
-INSTALL_FW_PATH specifies where to install the firmware blobs.
-The default value is:
-
- $(INSTALL_MOD_PATH)/lib/firmware
-
-The value can be overridden in which case the default value is ignored.
-
INSTALL_HDR_PATH
--------------------------------------------------
INSTALL_HDR_PATH specifies where to install user space headers when
to use it. It should be placed at the top of the configuration, before any
other statement.
+'#' Kconfig source file comment:
+
+An unquoted '#' character anywhere in a source file line indicates
+the beginning of a source file comment. The remainder of that line
+is a comment.
+
Kconfig hints
-------------
Use "make help" to list all of the possible configuration targets.
-The xconfig ('qconf') and menuconfig ('mconf') programs also
-have embedded help text. Be sure to check it for navigation,
-search, and other general help text.
+The xconfig ('qconf'), menuconfig ('mconf'), and nconfig ('nconf')
+programs also have embedded help text. Be sure to check that for
+navigation, search, and other general help text.
======================================================================
General
for you, so you may find that you need to see what NEW kernel
symbols have been introduced.
-To see a list of new config symbols when using "make oldconfig", use
+To see a list of new config symbols, use
cp user/some/old.config .config
make listnewconfig
and the config program will list any new symbols, one per line.
+Alternatively, you can use the brute force method:
+
+ make oldconfig
scripts/diffconfig .config.old .config | less
______________________________________________________________________
This lists all config symbols that contain "hotplug",
e.g., HOTPLUG_CPU, MEMORY_HOTPLUG.
- For search help, enter / followed TAB-TAB-TAB (to highlight
+ For search help, enter / followed by TAB-TAB (to highlight
<Help>) and Enter. This will tell you that you can also use
regular expressions (regexes) in the search string, so if you
are not interested in MEMORY_HOTPLUG, you could try
make MENUCONFIG_MODE=single_menu menuconfig
+======================================================================
+nconfig
+--------------------------------------------------
+
+nconfig is an alternate text-based configurator. It lists function
+keys across the bottom of the terminal (window) that execute commands.
+You can also just use the corresponding numeric key to execute the
+commands unless you are in a data entry window. E.g., instead of F6
+for Save, you can just press 6.
+
+Use F1 for Global help or F3 for the Short help menu.
+
+Searching in nconfig:
+
+ You can search either in the menu entry "prompt" strings
+ or in the configuration symbols.
+
+ Use / to begin a search through the menu entries. This does
+ not support regular expressions. Use <Down> or <Up> for
+ Next hit and Previous hit, respectively. Use <Esc> to
+ terminate the search mode.
+
+ F8 (SymSearch) searches the configuration symbols for the
+ given string or regular expression (regex).
+
+NCONFIG_MODE
+--------------------------------------------------
+This mode shows all sub-menus in one large tree.
+
+Example:
+ make NCONFIG_MODE=single_menu nconfig
+
+
======================================================================
xconfig
--------------------------------------------------
Searching in gconfig:
- None (gconfig isn't maintained as well as xconfig or menuconfig);
- however, gconfig does have a few more viewing choices than
- xconfig does.
+ There is no search command in gconfig. However, gconfig does
+ have several different viewing choices, modes, and options.
###
To configure the interval between learning packet transmits:
# echo 12 > /sys/class/net/bond0/bonding/lp_interval
- NOTE: the lp_inteval is the number of seconds between instances where
+ NOTE: the lp_interval is the number of seconds between instances where
the bonding driver sends learning packets to each slaves peer switch. The
default interval is 1 second.
.. include:: <isonum.txt>
+=========================================================
DPAA2 (Data Path Acceleration Architecture Gen2) Overview
=========================================================
The default value for each parameter is generally the recommended setting,
unless otherwise noted.
-Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
git.codelabs.ch / muen / linux.git / commitdiff